Catchsert (ใช้งานได้ทั้ง การสวมอัดด้วยความร้อนหลังและการสวมอัดด้วยความเย็น)
This insert nut has knurling in the same direction diagonally and is
excellent work efficiency from the symmetric design without orientation
A wide variety of size selection enhances convenience.
| Major insertion methods | Heat Staking Insertion, Ultrasonic Insertion, High-Frequency Insertion, Press-In Insertion |
| Material | Brass(C6801), Aluminum Alloy (made-to-order), Stainless Steel (made-to-order) |
| Plastic | Thermoplastics |
Features
- A wide variety of size selection enhances convenience
- Non-orientation design increases work efficiency
- Can be used for Heat Staking Inserts and Press-In Inserts
- Use lead（Pb）-free Brass
Dimensions
Catchsert Dimensions Drawing
Catchsert Dimensions Drawing
| Part Number | Thread and Pitch | A | B | C | Number of knurling |
Pilot Hole Diameter on Plastic (Reference) |
|
| CS3.3ーM2－2.0 | M2×0.4 | 3.30 | 2.00 | 3.00 | 1 | φ3.05 | ※ |
| CS3.3－M2－2.5 | M2×0.4 | 3.30 | 2.50 | 3.00 | 1 | φ3.05 | ※ |
| CS3.3－M2－3.0 | M2×0.4 | 3.30 | 3.00 | 3.00 | 1 | φ3.05 | ※ |
| CS3.3－M2－3.3 | M2×0.4 | 3.30 | 3.30 | 3.00 | 1 | φ3.05 | ※ |
| CS3.3－M2－3.5 | M2×0.4 | 3.30 | 3.50 | 3.00 | 1 | φ3.05 | ※ |
| CS3.3－M2－4.0 | M2×0.4 | 3.30 | 4.00 | 3.00 | 1 | φ3.05 | ※ |
| CS3.3－M2－4.5 | M2×0.4 | 3.30 | 4.50 | 3.00 | 2 | φ3.05 | ※ |
| CS3.3－M2－5.5 | M2×0.4 | 3.30 | 5.50 | 3.00 | 2 | φ3.05 | ※ |
| CS3.3－M2－6.0 | M2×0.4 | 3.30 | 6.00 | 3.00 | 2 | φ3.05 | ※ |
| CS3.3－M2－8.0 | M2×0.4 | 3.30 | 8.00 | 3.00 | 2 | φ3.05 | ※ |
| CS3.8－M2－3.0 | M2×0.4 | 3.80 | 3.00 | 3.50 | 1 | φ3.55 | ※ |
| CS3.8－M2－4.0 | M2×0.4 | 3.80 | 4.00 | 3.50 | 1 | φ3.55 | ※ |
| CS4.3－M2－3.0 | M2×0.4 | 4.30 | 3.00 | 4.00 | 1 | φ4.05 | ※ |
| CS4.3－M2－5.0 | M2×0.4 | 4.30 | 5.00 | 4.00 | 2 | φ4.05 | ※ |
| CS4.3－M2－6.0 | M2×0.4 | 4.30 | 6.00 | 4.00 | 2 | φ4.05 | ※ |
| CS4.3－M2－7.0 | M2×0.4 | 4.30 | 7.00 | 4.00 | 2 | φ4.05 | ※ |
| CS3.8－M2.5－2.5 | M2.5×0.45 | 3.80 | 2.50 | 3.50 | 1 | φ3.55 | ※ |
| CS3.8－M2.5－3.0 | M2.5×0.45 | 3.80 | 3.00 | 3.50 | 1 | φ3.55 | ※ |
| CS4.3－M2.5－2.5 | M2.5×0.45 | 4.30 | 2.50 | 4.00 | 1 | φ4.05 | ※ |
| CS4.3－M2.5－3.0 | M2.5×0.45 | 4.30 | 3.00 | 4.00 | 1 | φ4.05 | ※ |
| CS4.3－M2.5－3.5 | M2.5×0.45 | 4.30 | 3.50 | 4.00 | 1 | φ4.05 | ※ |
| CS4.3－M2.5－4.0 | M2.5×0.45 | 4.30 | 4.00 | 4.00 | 1 | φ4.05 | ※ |
| CS4.3－M2.5－5.0 | M2.5×0.45 | 4.30 | 5.00 | 4.00 | 2 | φ4.05 | ※ |
| CS4.3－M2.5－6.0 | M2.5×0.45 | 4.30 | 6.00 | 4.00 | 2 | φ4.05 | ※ |
| CS4.8－M2.5－3.5 | M2.5×0.45 | 4.80 | 3.50 | 4.50 | 1 | φ4.55 | ※ |
| CS4.8－M2.5－4.0 | M2.5×0.45 | 4.80 | 4.00 | 4.50 | 1 | φ4.55 | ※ |
| CS4.8－M2.5－5.0 | M2.5×0.45 | 4.80 | 5.00 | 4.50 | 2 | φ4.55 | ※ |
| CS4.8－M2.5－7.0 | M2.5×0.45 | 4.80 | 7.00 | 4.50 | 2 | φ4.55 | ※ |
| Part Number | Thread and Pitch | A | B | C | Number of knurling |
Pilot Hole Diameter on Plastic (Reference) |
|
| CS4.8－M3－2.0 | M3×0.5 | 4.80 | 2.00 | 4.50 | 1 | φ4.55 | ※ |
| CS4.8－M3－3.0 | M3×0.5 | 4.80 | 3.00 | 4.50 | 1 | φ4.55 | ※ |
| CS4.8－M3－4.0 | M3×0.5 | 4.80 | 4.00 | 4.50 | 1 | φ4.55 | ※ |
| CS4.8－M3－4.8 | M3×0.5 | 4.80 | 4.80 | 4.50 | 2 | φ4.55 | ※ |
| CS4.8－M3－5.0 | M3×0.5 | 4.80 | 5.00 | 4.50 | 2 | φ4.55 | ※ |
| CS4.8－M3－6.0 | M3×0.5 | 4.80 | 6.00 | 4.50 | 2 | φ4.55 | ※ |
| CS4.8－M3－7.0 | M3×0.5 | 4.80 | 7.00 | 4.50 | 2 | φ4.55 | ※ |
| CS4.8－M3－8.0 | M3×0.5 | 4.80 | 8.00 | 4.50 | 2 | φ4.55 | ※ |
| CS4.8－M3－9.0 | M3×0.5 | 4.80 | 9.00 | 4.50 | 3 | φ4.55 | ※ |
| CS4.8－M3－10.0 | M3×0.5 | 4.80 | 10.00 | 4.50 | 3 | φ4.55 | ※ |
| CS5.3－M3－3.0 | M3×0.5 | 5.30 | 3.00 | 5.00 | 1 | φ5.05 | ※ |
| CS5.3－M3－3.5 | M3×0.5 | 5.30 | 3.50 | 5.00 | 1 | φ5.05 | ※ |
| CS5.3－M3－4.0 | M3×0.5 | 5.30 | 4.00 | 5.00 | 2 | φ5.05 | ※ |
| CS5.3－M3－5.0 | M3×0.5 | 5.30 | 5.00 | 5.00 | 2 | φ5.05 | ※ |
| CS5.3－M3－5.3 | M3×0.5 | 5.30 | 5.30 | 5.00 | 2 | φ5.05 | ※ |
| CS5.3－M3－6.0 | M3×0.5 | 5.30 | 6.00 | 5.00 | 2 | φ5.05 | ※ |
| CS5.3－M3－6.5 | M3×0.5 | 5.30 | 6.50 | 5.00 | 2 | φ5.05 | ※ |
| CS5.8－M3－3.0 | M3×0.5 | 5.80 | 3.00 | 5.50 | 1 | φ5.55 | ※ |
| CS5.8－M3－4.0 | M3×0.5 | 5.80 | 4.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M3－5.0 | M3×0.5 | 5.80 | 5.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M3－6.0 | M3×0.5 | 5.80 | 6.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M3－7.0 | M3×0.5 | 5.80 | 7.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M3－9.0 | M3×0.5 | 5.80 | 9.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M4－3.0 | M4×0.7 | 5.80 | 3.00 | 5.50 | 1 | φ5.55 | ※ |
| CS5.8－M4－4.0 | M4×0.7 | 5.80 | 4.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M4－5.0 | M4×0.7 | 5.80 | 5.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M4－5.8 | M4×0.7 | 5.80 | 5.80 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M4－6.0 | M4×0.7 | 5.80 | 6.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M4－7.0 | M4×0.7 | 5.80 | 7.00 | 5.50 | 2 | φ5.55 | ※ |
| CS5.8－M4－8.0 | M4×0.7 | 5.80 | 8.00 | 5.50 | 3 | φ5.55 | ※ |
| CS5.8－M4－9.0 | M4×0.7 | 5.80 | 9.00 | 5.50 | 3 | φ5.55 | ※ |
| CS6.3－M4－5.0 | M4×0.7 | 6.30 | 5.00 | 6.00 | 2 | φ6.05 | ※ |
| CS6.3－M4－6.0 | M4×0.7 | 6.30 | 6.00 | 6.00 | 2 | φ6.05 | ※ |
| CS6.3－M4－8.0 | M4×0.7 | 6.30 | 8.00 | 6.00 | 3 | φ6.05 | ※ |
| CS6.3－M4－12.0 | M4×0.7 | 6.30 | 12.00 | 6.00 | 3 | φ6.05 | ※ |
| CS6.8－M4－5.0 | M4×0.7 | 6.80 | 5.00 | 6.50 | 2 | φ6.55 | ※ |
| CS6.8－M4－6.0 | M4×0.7 | 6.80 | 6.00 | 6.50 | 2 | φ6.55 | ※ |
| CS6.8－M4－7.0 | M4×0.7 | 6.80 | 7.00 | 6.50 | 3 | φ6.55 | ※ |
| CS6.8－M4－8.0 | M4×0.7 | 6.80 | 8.00 | 6.50 | 3 | φ6.55 | ※ |
| CS6.8－M4－11.0 | M4×0.7 | 6.80 | 11.00 | 6.50 | 3 | φ6.55 | ※ |
| CS6.8－M5－3.5 | M5×0.8 | 6.80 | 3.50 | 6.50 | 1 | φ6.55 | ※ |
| CS6.8－M5－5.5 | M5×0.8 | 6.80 | 5.50 | 6.50 | 2 | φ6.55 | ※ |
| CS6.8－M5－6.8 | M5×0.8 | 6.80 | 6.80 | 6.50 | 2 | φ6.55 | ※ |
| CS6.8－M5－8.0 | M5×0.8 | 6.80 | 8.00 | 6.50 | 3 | φ6.55 | ※ |
| CS6.8－M5－11.0 | M5×0.8 | 6.80 | 11.00 | 6.50 | 3 | φ6.55 | ※ |
| CS8.3－M5－5.0 | M5×0.8 | 8.30 | 5.00 | 8.00 | 2 | φ8.05 | ※ |
| CS8.3－M5－9.0 | M5×0.8 | 8.30 | 9.00 | 8.00 | 3 | φ8.05 | ※ |
| CS8.3－M6－6.0 | M6×1.0 | 8.30 | 6.00 | 8.00 | 2 | φ8.05 | ※ |
| CS8.3－M6－9.0 | M6×1.0 | 8.30 | 9.00 | 8.00 | 3 | φ8.05 | ※ |
| CS8.3－M6－13.0 | M6×1.0 | 8.30 | 13.00 | 8.00 | 3 | φ8.05 | ※ |
| CS11.3－M8－13.0 | M8×1.25 | 11.30 | 13.00 | 11.00 | 5 | φ11.05 | ※ |
※Standard Parts ・ Unit：mm
NOTE
- Pilot hole diameters are for reference only. The diameter should be determined by testing before use.
- Be careful of cracking resin when Catchserts are used for polycarbonate (PC) and other materials which
are sensitive to residual stress. - The diameter of the pilot hole for the object to be mounted should be smaller than the outer diameter of the
insert(Dimension C). - When inserts are tightened by screws, choose the screw length so that screws do not reach the bottom of
insert pilot holes. - The specifications are subject to change without notice.
- Please contact us if you have any other questions.
