Quality Lock (Insert nut สำหรับฉีดขึ้นรูปพร้อมกัน)
This is a revolutionary type of insert nut with a square groove in the middle.
Compared with conventional inserts with diamond knurling, the strength is significantly increased.
No cutting dust is generated, thus improving the quality.
| Major Insertion Method | Mold-in Insertion |
| Material | Brass (C3604), Aluminum Alloy (made-to-order) |
Features
- Revolutionary type of insert with a square groove in the middle
- In favourable conditions, the strength of this product will be doubled more than the strength of conventional inserts with diamond-shaped knurling
- Non-orientation design for higher productivity and workability
- No cutting dust is generated even during transportation, thus improving quality
- Full compliance with RoHS Directive
Dimensions
| Dimensional Drawing | Three-dimensional Drawing |
|
|
| Part Number | Thread and Pitch | A | B | Hole size before threading |
||
| QL-M2-3.0 | M2×0.4 | 3.20 | 3.00 | min 1.567 | max 1.679 | ※ |
| QL-M2-4.0 | M2×0.4 | 3.20 | 4.00 | min 1.567 | max 1.679 | ※ |
| QL-M3-3.0 | M3×0.5 | 5.00 | 3.00 | min 2.459 | max 2.599 | ※ |
| QL-M3-4.0 | M3×0.5 | 5.00 | 4.00 | min 2.459 | max 2.599 | ※ |
| QL-M3-5.0 | M3×0.5 | 5.00 | 5.00 | min 2.459 | max 2.599 | ※ |
| QL-M4-4.0 | M4×0.7 | 6.50 | 4.00 | min 3.242 | max 3.422 | ※ |
| QL-M4-5.0 | M4×0.7 | 6.50 | 5.00 | min 3.242 | max 3.422 | ※ |
※ Standard parts Unit.ｍｍ
Quality Lock Performance (Reference)
| Size | Pull-out（N） | Jack Torque(N・m) | Plastics |
| QL-M2-3.0 | 620 | 0.41 | ABS |
| Diamond Knurling M2 (Length: 3.0 mm) |
520 | 0.29 | ABS |
| QL-M3-3.0 | 1,008 | 1.22 | ABS |
| Diamond Knurling M3 (Length: 3.0 mm) |
810 | 0.91 | ABS |
| QL-M4-5.0 | 2,010 | 2.61 | ABS |
| Diamond Knurling M5 (Length: 5.0 mm) |
1,100 | 1.28 | ABS |
※ The strength largely depends on the plastic to be used. It should be tested in advance.
1N≒0.098kgf
1N-m≒9.8kgf-cm
1N≒0.098kgf
1N-m≒9.8kgf-cm
NOTE
- Headed inserts are also available.
- Please contact us if you need Pb-free material for environmental reasons.
- Choose the die pin diameter based on the dimension of the hole size before threading.
- The diameter of the pilot hole for the mounting object should be smaller than the outer diameter of the insert (Dimension A) if possible.
- When inserts are tightened by screws, choose the screw length so that screws do not reach the bottom of insert pilot holes.
- The specifications are subject to change without notice.
- Please contact us if you have any other questions.
